PPPoE

PPPoE Server Setup: Operating System: Ubuntu Desktop(8.04)

Installation of Softwares

Server Side

Необходими пакети

• Компилатор

apt-get install build-essential

• ppp

apt-get install ppp

• pppoe

apt-get install pppoe

• rp-pppoe, RP PPPoE може да се свали от http://www.roaringpenguin.com/files/download/rp-pppoe-3.11.tar.gz (да се провери актуалната версия)

wget http://www.roaringpenguin.com/files/download/rp-pppoe-3.11.tar.gz
tar -xf rp-pppoe-3.11.tar.gz
cd rp-pppoe-3.11
./go

go e бърз скрипт за конфигуриране. Въведете исканата информация. В края трябва да види:

• "Congratulations, it should be all set up!"

Настройки

Разгледайте директория /etc/ppp

cd /etc/ppp
ls 

chap-secrets              ip-down.d    options          pppoe.conf-bak
chap-secrets-bak          ip-up        pap-secrets      pppoe_on_boot
firewall-masq             ip-up.d      pap-secrets-bak  pppoe-server-options
firewall-masq-3.10        ipv6-down    peers            pppoe-server-options-example
firewall-standalone       ipv6-down.d  plugins          pppoe-up
firewall-standalone-3.10  ipv6-up      pppoe.conf       resolv
ip-down                   ipv6-up.d    pppoe.conf-3.10

Файловете, които най много ни интересеуват са:

• pppoe-server-options,
• pppoe.conf,
• options,
• pap-secrets,
• chap-secrets.

[PAP] e метода за удостоверяване по подразбиране, който ще остане. Ще се използват потребителите на операционната система.

Редактирайте файла pap-secrets:

nano pap-secrets

#
# /etc/ppp/pap-secrets
#

# INBOUND connections

# Every regular user can use PPP and has to use passwords from /etc/passwd
*       hostname        ""      *

# UserIDs that cannot use PPP at all. Check your /etc/passwd and add any
# other accounts that should not be able to use pppd!
guest   hostname        "*"     -
master  hostname        "*"     -
root    hostname        "*"     -
support hostname        "*"     -
stats   hostname        "*"     -
# OUTBOUND connections

# Here you should add your userid password to connect to your providers via
# PAP. The * means that the password is to be used for ANY host you connect
# to. Thus you do not have to worry about the foreign machine name. Just
# replace password with your password.
# If you have different providers with different passwords then you better
# remove the following line.
#       *       password

"test"  *       "test"

скрипт за стартиране DHCP

#!/bin/bash
# Starts the PPPoE server and turns on NAT


PROV=pppoe

#maximum number of addresses your server
#MAX=5

#lowest IP address your server is allowed

BASE=10.10.220.2
PLA=10.10.220.0/8

# NAT is the set of addresses which your server will
# NAT behind it. Other addresses behind your server
NAT=10.10.220.0/8
MYIP=10.10.220.1

##########################################
# Here is where the script actually starts executing.
##########################################

# Disable IP spoofing on the external interface.
#iptables -A INPUT -i eth0 -s $NAT -j DROP

# Enable NAT for the private addresses we hand out.
#iptables -t nat -A POSTROUTING -s $NAT -j $NAT --to-source $MYIP

# Launch the server.
pppoe-server pty -T 60 -I eth1 -L $MYIP -N $MAX -C $PROV -S $PROV -R $PLA

#echo "1" > "/proc/sys/net/ipv4/ip_forward"

Стартиране
За да стартирате сървъра изпълнете:
 pppoe-start
За да го спрете"
 pppoe-stop 
За да видите състоянието:
 pppoe-status